Zyxel Keenetic Air.

Settings

Step 1 of 1
Connect the cable to you in the apartment of our installers in the Internet port, and connect the computer to any of the yellow ports. You can also connect your PC with a router on a wireless network, but at the initial stage settings it is better to use a cable.

Step 1 of 6

Step 2 of 6

If the router has not yet been configured, the "Fast Setup NetFriend" page opens.
Press the "Web Configurator" button.

Step 3 of 6

If the Administrator Password window appears, in the "New Password" field and write a password to be used for further authorization in the router settings (we recommend using the Admin password).
In the "Enter Password again" again write the invented password.
Press the "Apply" button.

Step 4 of 6

Step 5 of 6

To configure the wireless connection, click on the "Signal Level" icon in the bottom panel of the indicators (in the middle).
Click on the "Access Point" or "Access point of 2.4 GHz".
Fill in the fields as shown below:

Network Name - Enter a name for your Wi-Fi network.
Network protection - WPA-PSK + WPA2-PSK.

Country - Russian Federation.
Standard - 802.11bn.
The power of the signal is 100%.

Step 6 of 6

If the menu has an "Access point of 5 GHz", click on it and adjust the 5 GHz network by analogy.
Fill in the fields as indicated below:
Enable Access Point - check the box.
Network Name - Enter the name for your Wi-Fi network and add "_5g".
Network protection - WPA2-PSK.
Network key - Enter the password to access your Wi-Fi network.
Country - Russian Federation.
Standard - 802.11An.
The power of the signal is 100%.
Enable WMM - check the box.
Click the Apply button (under the "Enable WMM" row).

Step 1 is3

Open the browser, in the address bar We write 192.168.1.1, press ENTER.

Step 2 of 3

At the first occur, if the router is not yet configured, the quick setup wizard will open. Click "Control Panel".

Step 3 of 3

On the left, in the "Internet" section, choose "wired"

1. To configure a new connection is not necessary, all the settings are made in the "Provider" tab.

Connection Priority: Main Connection
Schedule: works constantly

2. If there is an IPTV prefix (options), then you need to configure Bridge-port for correct operation.

From ports 4, 3, 2 or 1 you need to select the port in which the cable is inserted, which comes from the IPTV console and click on the arrow. The menu will open, select the TV prefix item.

3. IP Setup: Automatic (DHCP)

Even if your Static IP service is connected, this setting should always be auto.

4. Connection setting:

Type (protocol): L2TP;
Server address: tp.internet.beeline.ru;
Username: Your Facial Account (089 .., 085 ...);
Password: Your password from the Internet;
Authentication: Auto;
IP Setup: Auto

Wi-Fi Setup

Step 1 of 3

On the left, in the "My Networks and Wi-Fi" section, select "Home Network"

All settings are made in the Home Network tab.

Below will be the "Wi-Fi Wireless Wi-Fi Wi-Fi" and 5 GHz Wireless Network, the settings are the same.

Click "Advanced Settings"

Step 2 of 3

Advanced Wi-Fi settings will open.

Network Name (SSID): The Network Name that will be displayed in the Network List;
Hide SSID: Tanks should not be;
Schedule: It works constantly;
Network Protection: WPA-PSK + WPA2-PSK
Password: You need to come up with and record on a piece of paper (not to forget) password, not less than 8 characters.
Standard: 802.11bg;
Channel: Auto

Step 1 of 2

Click on the Globe icon in the bottom panel of the indicators (second left). The following page will appear.

Step 2 of 2

In the "Connections" section, select Broadband Connection and click on it.
In the "Ethernet Connection Setup" window in the "Use Connector" line, select the port for connecting the TV console (from 0 port not to remove it).
Click "Apply".

Use hardware reset settings if you want to configure the device again (delete all user settings), no access to the router settings interface web page, after setting the router, the Internet connection was not installed or the access password was lost.

Attention! When performing hardware reset, all user installations will be reset to factory settings!

On the device case there is an in-depth Reset button (Reset, Restore), which allows you to reset the settings for factory settings. You can find the reset, restore button on the same side of the router housing, where other connectors and buttons are located. In rare cases, the button can be located at the bottom of the router.

In order to reset the router settings to factory settings, follow these steps:
Turn on the router power and wait until the device is full. Click the Reset, Restore button using a pointed thin object (for example, a clip) and hold 30 seconds, then release the button.
After that, the router will reboot with default settings (factory settings) and retract it again.

Be careful by following instructions in this section. In case of error, the actions will require a visit to the service center to restore the device. It is recommended to flash the router by connecting the cable from the PC in any of the LAN ports. Firming a Wi-Fi router, there is a risk of obtaining an inoperable device, restored only in the service center, or not restored at all.

Step 1 of 4

Download the firmware.

Step 2 of 4

Open the browser, you type the address of the router in the address bar, press ENTER. The router's authorization page opens. Enter the login and password to access the router, press ENTER.

Step 3 of 4

You will find a web-interface of the router.
Go to the "System" menu. In the "Files" section (in early versions of the firmware, this section was called "Configuration") Click the name "Firmware" file.

Step 4 of 4

The "File Management" window appears, in which click the "Select File" button to specify the firmware file.
In the window that opens, specify the location of the file with the firmware for your device (file with the BIN extension).
Previously, you need to extract files from the zip archive with a firmware.
Click the Replace button to start the firmware update procedure.

Wait until the router updates its firmware, usually it takes no more than 15 minutes, do not turn off the router from the outlet network during the update. After the router updates its firmware and reboots, you can start exploiting.