Emachines E625 laptop analysis. Instructions for disassembling, assembling and cleaning from dust laptop Emachines G630

Settings

Cleaning a laptop Emachines from dust - This is the topic that the conversation about which will go in this article. Regardless of which brand, your laptop, sooner or later it will have to be cleaned, as well as change the thermal paste. Having worked on a certain time, it undergoes various problems. It may be overheating system, hang, malfunctions. All the blamed dust, in the process of which the normal heat sink is disturbed.

If you decide to clean the laptop yourself, the first thing you need to do is turn off the power cord and remove the battery. The next step will be disconnected internal devices. After unscrew all the screws and removed the back cover, it is necessary to carefully disconnect and remove the hard disk. For him will follow the RAM. It must be carefully removed from the grooves, pre-disconnecting the side mounts. The next extracted device will be a DVD drive. Its fastening is on the housing, which means it is already unscrewed, so you can just get it from the laptop housing.

Emachines Laptop Cleaning Process Description

Often happens that in the process cleaning laptop emachines Screws are lost, so it is better to immediately add them to some box and remove. And the internal devices extracted from the laptop can neatly decompose in such a way that it does not drop and damage any of them during cleaning.

Now the wireless connection sensor turns. If you are not a specialist and not a system administrator, then before disconnecting it is better to write down immediately or take a picture of the wiring to the sensor.

After making sure that the jacks left the screws are left, turn the laptop and carefully find the plastic latches with a screwdriver that hold the panel above the keyboard. Smoothly lift the panel to accidentally do not cut the wires and unscrew the screws that the keyboard is attached. After the keyboard was removed, you can remove the panel with speakers.

The next stage of disassembly will be display. To remove it, you need to disconnect the contact and unscrew all the bolts. Removing the lid under the keyboard, try not to damage the case. Now remove the motherboard.

The cooler shot from the cooling plate should be disassembled to clean the blade well. And from the surface of the plate itself, moistened with a cotton swab, remove the remains of the old thermal paste. It is better to clean the motherboard by means of blowing, and the rest of the places where there is dust gently wipe with a soft cloth. At the end of cleaning, you need to apply a new layer of thermal paste on the cooling plate and to dissolve it so that there is no clearance between the connection places. Now in the reverse order you can collect and connect all devices. The laptop is again as new and ready to serve you for a long time.

Often this is due to the fact that the fan of the laptop cooling system is tritely hammered by dust or something else (there have been cases when laptops brought in the SC, where the fan was clogged with feline wool). If the fan and radiator of the cooling system are dust - then the cooling efficiency is reduced, as well as the fan begins to be reinforced.

To fix it, you need to clean the laptop from dust. If there is time and opportunity, then it is better to trust this operation to the service center. But if I do not want to communicate with the service center - then it will be done manually to do the procedure.

Note: Lower the temperature of the processor and the laptop video card can also be shifted by the thermal paste. About how to produce it, described in this material:

To clean the cooling system, we will need:

Screwdrivers for removing the lid and fan

Napkin or cloth, as well as the possibility of compressor or a sphailed air sprayed can for blowing dust from the radiator

Lubricant for the fan (anyone suitable, but it is desirable that it was thick and did not spread quickly)

First you need to pull the plug from the power supply unit from the laptop, as well as remove the battery. Remove the laptop cover:

In more detail, the lid removal procedure is described in this material:

Note: If you do not know how to disassemble and collect your laptop, use the laptop disassembly instructions. You can find it in this topic forum :.

When disassembling a laptop, it should be remembered that except the bolts, the cover holds the latch. They need to go carefully.

When the lid was removed, we find the fan, unscrew the bolts:

Remove the fan itself:

Remove the impeller. Sometimes it happens that it is removed without much effort, and sometimes she keeps a plastic washer. To remove the impeller in this case, you need to reveal the sticker on the back and the needle gently remove the washer. With a washer worth being neat. It is very easily lost.

After that, pull out the impeller:

To brush the blades, you can use the folded twice with a napkin or an ordinary cloth.

Clean piece of napkins wipe the shaft of the impeller and put a little lubricant on it

Now no less important operation - dust removal from radiator . For this, I recommend using brushes, dry rags, squeezed air cans or compressor. In the extreme case, you can with a vacuum cleaner or with all the power of the bottom. The goal is simple - to blow from the gaps between the plates of the radiator all the dust.

This is how the scored radiator is like this (these three photos are taken from the site azbooki.ru):

All dust and other garbage stands from there to clean. As a result, such a clean radiator should be obtained:

When you finish, we collect everything as it was, tighten all the bolts and put the battery. On this procedure, cleaning can be considered finished

Removal of small scratches and fat spots from the surface of the laptop

Let me assume that most of the users of laptops prefer to see their devices clean and beautiful. The laptop, which is covered with fingerprints, traces of dirt, scratches, does not look very represented.

To fix it like that, we need:

Wet wipes for wiping LCD monitors (you can easily find them in stores)

Ragged with microfiber (in the same stores). It looks like that

Displex polishing paste or any other scratch to remove scratches

Complete with such pastes often napkins:

There are such pastes relatively cheap (2-10 $)

First of all, you need to clean the monitor from were from fat traces. To do this, it is necessary to blow the first thing to blow or very carefully to move dust from the matrix, then wipe with a wet cloth, and then a cloth with microfiber. If the dust before the procedure is not easy, then you can scratch the matrix. The laptop cover is similar in the same way: first blow / eat dust, clean the wet cloth and wipe the microfiber.

And now I will describe the removal process of shallow scratches with a glossy lid. It so happened that some models of laptops are equipped with a glossy lid and elements of the housing that look very beautiful, but scratches often appear on such surfaces. To remove them, we will need polishing paste (Dislex, Digitex, and GOI, but very carefully, because its grain is large), a napkin or cotton. Before polishing, the laptop directly, I recommend stretching on damaged scratched CD discs. We apply a little polishing fluid to the scratch

and three ... option is possible that it will come once again to the polishing fluid and rub with a cotton or a napkin again. A couple of minutes, a shallow scratch will disappear in the same way to get rid of scratches on mobile phones, players and other gadgets.

ATTENTION: In no case cannot be removed in such a way of scratching from LCD screens !!!. When polished, a small upper layer of material is removed and it may damage the LCD matrix /

After the end of polishing, we wipe the place with a wet cloth and microfiber.

If after reading this material, there were still questions, we ask them in this topic theme:

Edited: Fuzzyl - September 15, 2013
Cause: Material version 2.1

Today I will tell you how the emachines laptop disassembled model G630.
He survived the fall, the matrix of it is broken and the body is slightly damaged, but it turns on.

Disassembly laptop starting with the fact that we turn off the battery.
Unscrew the five screws to the holder on the bottom panel of the laptop.
Open the first compartment, there is a hard disk.
I pull it out by pulling the tongue, and remove it.
The compartment from the opposite side is also designed for the hard disk.
On average, memory is memory and Wi-Fi module.
Remove memory.
Expand the laptop and look at how the keyboard is attached.
Remove the protective bar above the keyboard.
We raise this bar approaching from the edge, decline all the latches.
Further removing the keyboard, the upper part is rejected by yourself, drawing off all the latches from the bottom and from the edge.
Do not pull, as you can damage the train.
Move the loop by moving the mounting on yourself, pull out the plume from the connector.
We remove the keyboard.
To get to the cooling system, you need to remove the matrix.
You unscrew the two bolts on both sides under the loops, the bolts around the perimeter and the bolt that holds the drive.
Total odent bolts.
Remove the wires of the Wi-Fi module antenna, they are enough to pull upstairs.
These wires are in the groove, opening the laptop these wires must be pulled out.
We disconnect the connector on the matrix, you need to pull out exactly differently we can spoil the loop.
Remove the latches hiding hinge.
Twisting two bolts on both sides, they hold the matrix.
Disconnect the matrix from the laptop.
Unscrew all screws under the bar and keyboard.
At the top under the plugs there are four more bolts, they also need to unscrew.
Pull out the drive.
Pathing a thin object between two half a laptop, disgust all the latches around the edges.
Before lifting the cover, turn off all visible connectors.
This is the connector on the speakers, the connector on the left speakers, the connector on the buttons panel and the connector on the touchpad.
After the entire loop is eliminated with a lid.
To get to the cooling system, you need to remove the motherboard.
We remove the Wi-Fi module, it is located on the middle hatch and keeps on two bolts.
Next, you need to find the screws marked with a triangle they are attached to the motherboard.
Unscut them, and remove the motherboard.
Thus, they got to the cooling system, and she scored dust.
If the laptop is in operation for two three years, then remove the cooling system completely and change the thermal paste.
In this case, the laptop is in operation one year, so we just unscrew the cooler for cleaning.
First, we disconnect the power, then unscrew the three bolts on top of a thin screwdriver.
Raise the cooler and clean it.
We start the reverse assembly process.
We put the cooler in place, connect the power.
We screw the cooler for three bolts.
We take the bottom of the case and install the motherboard in it.
Insert your motherboard under the tilt.
Insert the Cartride Cutter.
We screw four bolts that kept the motherboard.
Install the Wi-Fi module in place, screw it into two bolts.
Now we put the top panel, snap it around the perimeter.
Connect all connectors.
We screw the four bolts that were closed with stickers, close them back.
We screw the remaining bolts.
Insert memory into the middle slot at the bottom of the laptop.
Now install the matrix, and screw the four bolts.
Connect the matrix connector.
We lay the loop into their channels, where they must pass.
Propy the wires in the groove, and stretch from the bottom.
Connect the wires to the Wi-Fi module.
We put an optical drive in place.
On the bottom panel of the laptop, we screw all the bolts.
Insert a hard drive.
We put the lids in place and screw them with screws.
Open the connector key and insert the keyboard loop, insert it smoothly.
Close the connector key.
Install the keyboard in place and above cover the decorative lid.
Return the battery.

You can see the video by clicking on the link:

The Welkomp service center in Kharkov entered a laptop with symptoms - do not turn on. During the diagnostics, the cooling system was discovered. In this article, you will show how to disassemble the laptop at home yourself. Disassembly requires some experience, so if you are not sure about your abilities - refer to.

Turn the laptop. Slide the battery lock in the direction with an open lock icon. Slide and hold the battery latch to the shutter position, then remove the battery from the main unit.

How to remove the keyboard?

Turn the laptop and completely open the lid. There are five locks that need to be released in order to remove the keyboard.
Both hands gently lift the keyboard board and turn it onto the stand stand.
Unlock the keyboard connector and disconnect the cable. Set the keyboard away.
Unlock the connector and disconnect the touchpad trailer back from the motherboard.

Removing a DVD drive

remove one drive fastening screw from the bottom of the housing.
Grasp the drive panel on the front panel and pull it out of the housing. Remove the drive plug panel, pressing the top edge down.
Remove the two screws fixing the drive bracket and remove the bracket.

We turn over the laptop and remove the keyboard module and the control button.

We unscrew all the screws on the top of the case. We unscrew the loops and remove the matrix cable from the connector. Turn off Wi-Fi antennas and then remove the screen.

With the help of a radiator, we split part of the case and pull out the motherboard. Previously, do not forget to unsubscribe 1 screw with a system board that secures it to the bottom of the case.

We clean the brush motherboard.

We disassemble the cooling system. To do this, we unscrew the 3 screws holding the cooler on the motherboard. The bottom photo shows the replaced power connector.